bioncam.blogg.se - Acrylic to cover desk

#ACRYLIC TO COVER DESK HOW TO#
#ACRYLIC TO COVER DESK SERIES#

Press the sheet firmly against the wall, allowing the foam tape to spread and adhere to the largest surface area possible, then leave it for a time until the adhesive has fully taken effect and you are certain that the sheet and the substrate are securely bonded. Once you are certain that it is straight against the wall, preferably with the use of a spirit level, gently reduce the angled gradient of the sheet until all of it is completely flat against the substrate. So long as you have met the 3 criteria set out above, go ahead and remove the paper from the rows of double sided tape and once again hold the top edge of the sheet against the wall, at a 45° angle. This is your last chance to make sure that everything is as it should be before you apply the sheet to the substrate, so take your time to make sure that it is the right size, that it will fit properly, and that you are happy with how it should look.

For the best results we suggest you apply the tape in evenly spaced horizontal strips along the width of the sheet.īefore removing the paper from the other side of the tape hold the top edge of the sheet at a 45° angle along where you want it to be.

we suggest using double sided foam tape, the strength of which is more that sufficient to connect an acrylic sheet to a wall. Once you have been able verify that it is capable of supporting the load without any hassle, you can now remove the protective film from the side of the sheet that will be facing the wall and clean it, preferably with petroleum ether or isopropyl alcohol.Īt this juncture you can resort to a number of bonding agents, including double-sided tapes, silicone, acrylic adhesives, etc. We suggest you do this by taping the acrylic to the substrate, which should give you a clear indication of whether or not the surface has the load-bearing capacity to support the sheets and the tape which shall be used in the permanent fixing. One thing you should most definitely do before applying your acrylic sheet is to ensure your chosen surface can actually support the acrylic sheets that you wish to mount.

#ACRYLIC TO COVER DESK SERIES#

This means once you have applied the acrylic to its new under-layer any mistakes made cannot be corrected it is for this reason that we suggest you carry out a series of practice runs with the protective film still on, before removing it and attempting it for real. The method of installation that we shall be describing is one that shall permanently fix the acrylic to a substrate.

#ACRYLIC TO COVER DESK HOW TO#

To quickly recap, ensure that both your acrylic and substrate are properly readied, and that all the machining has been fully carried out if you have not done this yet and are unsure how to then please refer to the previous article.

VuPlex Plastic Cleaner and Anti-Static Polish SprayĬontinuing on from our previous article ‘ Preparing for installation‘ we shall now be detailing to you the best method of installing acrylic sheets onto a substrate surface.

Foamex Integral Foam PVC Flat Cut Letters.

All Dell, so the black monitor, mat, keyboard etc. They have a large - must be around 2' x 1.5' desk mat under their keyboard, in black. I made a computer unit for my in-laws like this. Get a large mat for under the keyboard, and use a mousey one for the, er, mouse. Solution, apply a few wipe-overs with furniture polish. One possible snag with water-based satin is that it can feel 'tacky' for months afterwards - not the tackiness from not drying out properly, but anything left sitting on it will tend to stick a bit! (Some are more prone to this than others.) Water based stuff will need at least 3 coats, but is so much easier to use. If the trim has a decor profile, use a brush to finish this off instead of the roller. Finish off with light rolling and it will dry to a very fine and attractive texture. I've then used quick-drying (water-based) satin applied, as mentioned above, with a foam roller. Wipe every trace of dust off really well. The edges of the MDF will require careful attention, tho' I presume you have wood trim finishing this off instead? Apply a couple of coats of quick-drying MDF (or 'wood') primer, then sand down to get a smooth finish.